TradeReign
Back to HomeEducation HubCompatibilityAboutDisclosures
Tradovate Charting

How to Add VWAP on Tradovate Check Which Trades Your Line Includes

VWAP weights prices by volume. A period that includes trade before the U.S. cash open can put the same MES close on the opposite side of VWAP from a cash-open calculation. Use these steps to see which calculation you are looking at.

Quick Answer

On a Tradovate Web chart, hover over the chart and open Indicators. Find Volume Weighted Average Price (VWAP) in the built-in list and select it. Before comparing the line with TradingView, match the dated contract, bar interval, and calculation session.

Start 7-Day TrialMore Guides

Add the built-in VWAP to a Tradovate Web chart

Open the Chart module and choose the dated contract you intend to review, such as the active MES expiry. Select regular five-minute candles. Hover over the chart to display its controls, open Indicators, and select Volume Weighted Average Price (VWAP) from the built-in indicator list.

Check the chart legend for the study and confirm that the line is visible. If the chart already has a VWAP, check which result is the built-in study and which came from a community indicator before comparing them. Use the chart’s indicator controls to review the installed study’s settings. Only use a setting that appears on your selected study.

If you can’t find it, confirm you are looking at the Chart module’s Indicators menu in Tradovate Web. The community catalog is a separate list of user-published studies. Check the selected study’s calculation and reset behavior before carrying a third-party VWAP into your setup.

Compare a pre-open sample with a cash-open start

Switch the chart below between the two calculations. Both use the same five-minute candles and the same bar-price approximation, HLC3. The earlier calculation includes 400 fictional contracts traded from 9:10 to 9:30 a.m. ET. The cash-open calculation starts at 9:30 and includes the 300 contracts in the next two completed bars. A full electronic-session calculation can include more history than this short sample.

At 9:40 ET, the earlier start gives a VWAP of 5,998.34. Starting at 9:30 instead gives 6,001.72. The 6,000.75 close is above the first line and below the second. A replay rule requiring a close above VWAP would score that same candle differently. Write down the intended start before reviewing the signal.

To identify which trades your installed Tradovate study includes, check what happens to the line at the intended boundary. Check the reset even when the chart hides overnight candles.

Same MES close, two VWAP starting points

Synthetic MES 5-minute candles. Times are bar closes in ET.

At the 9:40 ET close, fictional MES closes at 6,000.75, above the 5,998.34 VWAP that includes the earlier sample bars.

Why Tradovate VWAP can differ from TradingView

Open the same dated contract on both platforms. Match the candle type, interval, and time zone. Compare the actual high, low, close and volume for one completed candle first. If those inputs differ, check the symbol, feed delay, and chart session before comparing the indicator.

Next, compare the first bar after the intended reset and one later completed bar. Check the reset point and calculation source when the study exposes them. A trade-by-trade calculation and a calculation that gives each bar one representative price can disagree even with the same total volume. Record which method your study uses when the documentation or settings identify it.

In Tradovate Web, the instrument’s Time Frame setting lets you compare a Custom cash-hours view with a 24 Hours view. Keep both charts on the same interval. Use that comparison to see which candles were removed, then check the VWAP separately. If the required calculation window isn’t available in the study, use a documented indicator that supports it and verify its first included candle.

Sources

Official References

Platform details on this page were checked against these official resources.

Tradovate Web indicatorsOpen the Chart module’s Indicators menu and find the built-in VWAP listing.Tradovate community indicatorsFind the separate catalog of user-published indicators.TradingView’s VWAP calculation and inputsCheck the reset period, price source, and timeframe when comparing two platforms.
Related Guides

Keep Building the Rule System

Compare Tradovate’s cash-hours and 24 Hours charts

Check which prices and candles the chart session removes.

Set up VWAP in TradingView

Find the built-in indicator, select the calculation interval and check the anchor.

Practice reading a VWAP pullback

Compare a reclaim and a failure using completed MES bars.

FAQ

Common Questions

Does Tradovate Web have a built-in VWAP indicator?

Yes. Tradovate’s Web indicator documentation lists Volume Weighted Average Price (VWAP). Open Indicators from the chart controls to select it.

Why does VWAP look different on Tradovate and TradingView?

Compare the same dated contract and completed bars first. Then check the indicator’s start time, the volume and price used in the calculation, and the calculation interval.

Risk Disclosure

Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.

TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.

Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.