Read the ATR in points
Use a completed bar on the timeframe and session defined in your plan.

Enter ATR in price points from a completed bar and the multiplier in your plan. The example starts with hypothetical MES values. Change ATR from 4.10 to 8.10 to see how the same budget fits fewer contracts.
Micro E-mini S&P 500 (MES): $5.00 per point; 0.25 points per tick; $1.25 per tick. Stop distance is the absolute difference between entry and protective stop, for either a long or a short.
ATR × multiplier is 6.15 points before rounding. The long stop price is 5,993.75.
Stop used: 6.25 points / 25 ticks. Rounded up to the next whole tick to avoid understating risk. Stop-only risk per contract: $31.25. Including your allowance: $34.25.
The proposed contracts fit your entered risk budget under these assumptions.
Estimated risk = contracts × (stop points × dollars per point + per-contract cost allowance). Budget-based count = budget ÷ estimated risk per contract, rounded down. An optional cap can only reduce that count.
Replace the example $3 allowance with your own estimate for round-trip commissions, fees and slippage. Stops do not guarantee a fill price or maximum loss. This is not a margin, buying-power, account-eligibility, or prop-firm compliance check. A contract cap here applies only to the selected instrument; it does not convert mixed micro/mini positions or reserve capacity for other open trades.
Tick-value chart and CME contract specifications. Educational estimates only. Verify current specifications and account rules before trading.
Synthetic MES 5-minute candles. Times are bar closes in ET.
The 9:40 candle closes at 6,000.00. The 9:45 candle ranges from 6,003.25 to 6,005.50. Its high-to-low range is 2.25 points, but its true range is 5.50 points because the prior close was below that candle.
Use a completed bar on the timeframe and session defined in your plan.
An MES tick is 0.25 points. Use the actual increment for your contract.
Multiply ticks by tick value, add estimated costs, then round the resulting contract count down.
Assume a 6,000.00 long entry, a 1.5× multiplier and a $3 estimated round-trip allowance per contract. The ATR readings below are separate hypothetical inputs. One MES tick is $1.25.
The wider stop fits fewer contracts at the same budget. Use the rounded stop distance for sizing. Actual losses can exceed the estimate if fills slip or price gaps through a stop.
Open a standard candlestick chart for your selected dated futures contract. In Indicators, search for Average True Range and select the built-in indicator. Under Inputs, note the length and smoothing. TradingView defaults to RMA smoothing. The length is expressed in bars, so a 14-period ATR on a five-minute chart responds to five-minute ranges and a daily ATR responds to daily ranges.
Keep the chart interval and session fixed when comparing readings. A session that skips overnight bars can change the gap from the preceding close, and a contract roll can change what price series you are measuring. Record the ATR at your chosen completed decision bar. A still-forming bar can change the reading.
True range is the largest of three distances. Compare high minus low, the absolute distance from high to the prior close, and the absolute distance from low to the prior close. The synthetic gap bar’s values are 2.25, 5.50 and 3.25 points. True range is therefore 5.50 points. ATR smooths a series of these ranges over time.
Multiply ATR in points by the plan’s multiplier, then divide by the tick size. When that distance is a minimum, round the tick count up and multiply by tick size to get the actual distance. In the first example, 6.15 divided by 0.25 is 24.6. Round up to 25 ticks, or 6.25 points.
For a long, subtract the rounded distance from the entry. For a short, add it. With the same 6,000.00 entry and 25 ticks of distance, the short stop would be 6,006.25. Reconcile the calculation against the actual entry fill and check the intended closing side, quantity and stop type in the trading platform.
An ATR line or a chart drawing is a planning reference. Verify the working order separately. If the plan freezes the distance at entry, write down that value so a higher ATR later in the trade does not quietly widen the stop.
An ATR multiple gives the planning rule a volatility input. It does not identify the price that invalidates the trade idea. For a setup defined by a swing low or range boundary, write down what happens when the calculated stop sits inside that level. An example rule can require the stop beyond both levels, then reduce size or skip the trade if the budget cannot fit one contract.
To evaluate a multiplier, hold entry rules and data settings fixed. Record what ATR was known at each entry and test the stop with the rounded distance, realistic costs and the same dollar budget across periods. Keep trade count and net results alongside stop-out frequency. One multiplier can reduce stop-outs while also increasing risk per contract and reducing size.
Platform details on this page were checked against these official resources.
Enter futures ticks or points, dollar risk and estimated costs.
See why the same stop distance changes risk across contracts.
Check actual working orders after you enter a trade.
Use excursion data to investigate a proposed stop or exit change.
The standard ATR is in the instrument’s price units. On MES, divide ATR in points by 0.25 to express it in ticks. The ATR% indicator expresses a percentage instead.
The length is 14 bar periods. On a five-minute chart, each bar is five minutes. On a daily chart, each bar is one trading day. With RMA smoothing, older observations still carry diminishing weight.
An initial ATR stop defines the entry-time distance. An ATR trailing stop uses a separate rule to move the working stop as the trade develops. Define the recalculation schedule and which direction the stop may move before testing it.
Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.
TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.
Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.