TradeReign
Back to HomeEducation HubCompatibilityAboutDisclosures
Futures Trading Journal

MAE and MFE in Futures Trading Measure What Happened While You Were In the Trade

A trade that closes up two points might have gone six points in your favor or barely made it past the exit. The final result alone gives you no way to tell. Record both excursions to see which entries put you under pressure and which exits gave back an open gain.

Quick Answer

Maximum adverse excursion (MAE) measures the furthest price moved against your entry while the trade was open. Maximum favorable excursion (MFE) measures the furthest it moved in your favor. For a long, measure MAE down to the low and MFE up to the high. For a short, measure MAE up to the high and MFE down to the low.

Start 7-Day TrialMore Guides

One price path, a long and a short

Synthetic MES 5-minute candles. Times are bar closes in ET.

Both examples enter at the open of the first candle and exit at the close of the last. The window spans prices from 5,997.00 to 6,006.00. For the long, the low determines MAE and the high determines MFE. For a short on the same path, the roles reverse.

MAE

Measure the worst move from entry during this individual trade.

MFE

Measure the best move from entry during the same window.

ETD

End trade drawdown measures the gap between the best open result and the exit result on the same unit and cost basis.

Comparison

Calculate both excursions from the same synthetic MES candles

Assume one contract, entry at 6,000.00 and exit at 6,002.00. The observed high is 6,006.00 and the low is 5,997.00. MES moves in 0.25-point ticks and is worth $5 per point. Excursions below are written as positive distances.

Measure
Long at 6,000.00
Short at 6,000.00
MAE
3 points down · 12 ticks · $15
6 points up · 24 ticks · $30
MFE
6 points up · 24 ticks · $30
3 points down · 12 ticks · $15
Gross exit P&L
+2 points · +$10
−2 points · −$10
Gross ETD
$30 − $10 = $20
$15 − (−$10) = $25

The chart shows invented prices for two independent trade examples. The open extremes describe the path. Simulated or live orders may fill at other prices, and commissions change net P&L.

Measure only the time your position was open

Start with one contract and one entry and exit. Record the dated symbol, side, fill timestamps and fill prices. Use the lowest and highest prices reached between those fills. Using positive magnitudes, a long’s MAE is entry minus low and its MFE is high minus entry. For a short, MAE is high minus entry and MFE is entry minus low. Count a zero when there was no movement on that side of entry.

When a fill lands mid-bar, that bar’s full high or low may include prices from before entry or after exit. Review finer data within the fill window if you have it. Flag approximate values when you only have complete candles, and leave a missing measurement blank rather than replacing it with zero.

For multiple lots entered together and held at a fixed quantity, multiply the point move by the contract’s dollar value per point and quantity. For scale-ins and partial exits, use the platform’s paired legs or calculate the excursions of the position’s equity path with its changing size. Record which method you used. The full trade’s largest size may have been different when the extreme occurred.

Find MAE and MFE in NinjaTrader and TradingView

In NinjaTrader Desktop, open Control Center → New → Trade Performance. Choose the matching account and dates, generate the report and select Trades. Inspect the trade’s MAE, MFE and ETD alongside its timestamps and quantity. Right-click a row and select Chart to locate it. If you have multiple strategies in the same account, check how the report paired executions.

In TradingView, add your strategy and open Strategy Report → Trades. Find the row’s Favorable excursion and Adverse excursion values next to the trade result. Use the strategy’s simulated fill times for matching. This workflow reviews the strategy report. For a manually executed trade, pair your actual fills and measure the intervening price path.

Keep data source and units with each journal observation. NinjaTrader documents that live statistics can include bid and ask prices the chart does not show, while backtests can use bar extremes. Feed gaps, different entry timing and different fill models can all change the numbers.

Use the metrics to test a specific journal question

Start with one setup and take every completed trade in a defined date window, including losers and scratches. Record MAE and MFE in ticks or as multiples of the initial planned risk. Add the exit reason and net P&L after costs. Compare like sessions and exit rules so a long hold and a scalp don’t quietly answer different questions.

For a simulated example, the long above first traded down three points, then up six. A two-point stop would have been reached before the six-point rise. If you only look at the eventual winner’s MFE, you miss that ordering. A trade already stopped in your journal gives no evidence about what happened while it would have been open with a wider stop. Replay from the original entry when testing that change.

Write one stop or target change before reviewing a new sample. Replay it without seeing future bars, with the same position-sizing and cost assumptions. Track net expectancy and drawdown alongside the excursions. When a stop and target lie within the same candle, inspect finer data or record the sequence as ambiguous.

Sources

Official References

Platform details on this page were checked against these official resources.

NinjaTrader Trade Performance statisticsCheck data sources, units and platform calculation conventions.NinjaTrader performance displaysFind the Trades columns and chart view.TradingView favorable excursionLocate the strategy report column.TradingView adverse excursionVerify the corresponding adverse excursion column.CME MES contract specificationsVerify the tick increment and dollars per point.
Related Guides

Keep Building the Rule System

Calculate an ATR stop distance for futures

Round a TradingView ATR-based stop to valid ticks before sizing the trade.

Build a futures trading journal

Record setup, fills, costs and execution notes before adding path measurements.

Calculate net expectancy

Use closed trade results after commissions and fees.

Export NinjaTrader trades

Verify the account, dates and units before exporting.

Audit TradingView strategy fills

Check modeled order timing, intrabar detail and costs.

FAQ

Common Questions

Is maximum adverse excursion the same as maximum drawdown?

MAE measures a single trade’s worst move relative to entry. An account’s maximum drawdown measures the largest peak-to-trough decline in its equity over the period being reviewed.

Can a losing trade have a positive MFE?

Yes. It can move in your favor while open and then reverse before you exit. The synthetic short in this guide sees three favorable points, then closes with a two-point gross loss.

How do you calculate MAE and MFE in R multiples?

Convert the excursion to dollars, then divide by the original planned dollar risk for that position. Use the same initial risk reference for both and record whether the risk denominator includes costs.

Risk Disclosure

Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.

TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.

Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.