Use the fill prices
Use executions from the broker. A chart level or average price can hide the individual prices and sizes.

Enter actual fills for one completed trade. The example has two exits and $3 in total fees. Enter 0 if there were no fees.
Net profit or loss
$11.00
Gross $14.00. Fees $3.00. 2 contracts at $0.50 per tick per contract.
Use executions from the broker. A chart level or average price can hide the individual prices and sizes.
The total contracts entered and exited must match for the completed trade.
Add the exchange, clearing, and broker charges you paid on both sides of this trade.
Two MNQ enter long at 20,125.00. One exits at 20,130.00 and earns $10 gross. The other exits at 20,127.00 and earns $4 gross. MNQ is worth $2 per point per contract, so the two exits earn $14 before fees.
If the total transaction cost is $3 for both sides, subtract it once to get $11 net. Enter the two exits on separate lines so the quantities stay attached to the correct prices.
A trade can exit at its entry price and still lose its fees. For a single exit at the full size, divide total round-trip costs by the dollar value of one tick for the position. For two MNQ worth $0.50 per tick each, one tick pays $1.00. If the combined costs are $2.70, the first whole tick that covers them is three ticks, or 0.75 points. A two-tick gain leaves a $0.70 loss. Three ticks leave $0.30 after fees.
After a partial exit, calculate break-even for the whole trade separately from the profit or loss on the remaining contract. In the calculator’s default example, two MNQ entered long at 20,125.00 and the first one exited at 20,130.00 for a $10 gross gain. Using $3 in total projected fees across all four contract sides, the last contract can lose $7 gross before the full trade turns negative.
At $2 per point on the one remaining MNQ, that $7 covers 3.50 points below the original entry. A final fill at 20,121.50 puts the full trade at $0.00 after fees. A fill one tick lower, at 20,121.25, gives a $0.50 net loss. To check both outcomes above, leave the first exit and total fees unchanged and replace only the second exit price.
When the calculated threshold falls between outright ticks, round the required exit price up for a long or down for a short to find the first valid price with net P&L of at least zero. This assumes a fill at the modeled price and costs as entered. A stop’s trigger can differ from the fill. If you use actual executions, their prices already include slippage.
For a short, a lower buy-to-cover price produces a gross gain. One hypothetical MCL sell at 72.40 covered at 72.47 loses seven ticks at $1 each. With $2 in fees, the net result is a $9 loss.
If an individual fill price is between valid outright ticks, recheck the execution details. A weighted average across several fills can legitimately sit between ticks. Enter the individual fills to keep the arithmetic tied to the actual prices.
Use the same dated contract, completed lot quantities, and commission scope as the report. A position reversal can close one trade and open another with the same execution. Allocate the closing and opening quantities to the respective trades before adding the rows.
Actual fills already include the effect of getting filled away from the planned price. Record slippage as a separate comparison when you journal the trade. Deducting that amount again from fill-based P&L would count the same price difference twice.
Platform details on this page were checked against these official resources.
Trace the differences in entry, exit slippage and fees through one MES example.
Check fills, per-side costs and the commission template used by the selected account.
Compare current fills and a proposed add at the same modeled stop.
Choose the correct account, dates, and report, then check fee totals.
Convert ticks or points to dollars and check the contract specifications.
Read Treasury note quotes in 32nds and convert the price move to ticks.
Compare whole contract counts under a stop, cost allowance, and risk budget.
Track costs, partial exits, and results in dollars and R.
Use net results to review a sample of trades.
A fill at the entry price produces zero gross P&L on that quantity. Whether your whole trade breaks even depends on all entry and exit fills, position size, and total costs.
Yes. Add each exit as a separate fill. The total exit quantity must equal the total entry quantity for the completed trade.
Subtract all transaction fees for the trade from gross P&L. When using actual fills, their prices already reflect execution differences from your plan.
Individual executions are tied to specific quantities. A weighted average can fall between ticks even when every execution was at a valid price.
Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.
TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.
Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.