TradeReign
Back to HomeEducation HubCompatibilityAboutDisclosures
ICT Concepts for Futures

ICT Dealing Range: Premium, Discount and Equilibrium Read the Annotated Futures Charts

At 9:50 a.m. New York time, the same fictional MES candle closes at 6,004.00. It sits above the midpoint of a smaller intraday range and below the midpoint of a broader range. Compare the two views, then see what changes when the inner range expands.

Quick Answer

A dealing range is the interval between a selected high and low. Its midpoint is equilibrium. Within that range, prices above equilibrium are in premium and prices below are in discount. The label always depends on which high and low you chose.

Start 7-Day TrialMore Guides

Dealing Range chart examples

Synthetic MES 5-minute candles. Times are bar closes in ET.

The 5,998.00–6,008.00 inner range gives 6,003.00 equilibrium. At 9:50, the 6,004.00 close is one point above it and inside the range.

Premium in the inner range

The 5,998.00–6,008.00 inner range gives 6,003.00 equilibrium. At 9:50, the 6,004.00 close is one point above it and inside the range.

Discount in the broader range

The same bars are shown against a previously marked 5,990.00–6,020.00 range. Its midpoint is 6,005.00, so the same 6,004.00 close is one point below it.

Range expands later

The 10:00 high reaches 6,012.00. The next candle’s lower high confirms the new pivot at 10:05 under this drill’s rule. With the original low, the updated equilibrium is 6,005.00 and the later 6,004.00 close is in discount.

Comparison

Classify the same 6,004.00 price

Calculate each midpoint as (high + low) ÷ 2. Compare the close with that reference.

Range
Equilibrium
6,004.00 close
Inner · 5,998.00 to 6,008.00
6,003.00
Premium at 9:50
Broader · 5,990.00 to 6,020.00
6,005.00
Discount at 9:50
Updated inner · 5,998.00 to 6,012.00
6,005.00
Discount at 10:10

Record the range and the time it became usable. Keep earlier labels tied to the range available at the time.

Choose the range before judging premium or discount

Write down the instrument, time frame and purpose of the range. For the inner replay example, freeze the highest high and lowest low of the three bars ending at 9:45. The broader high and low were marked from earlier bars outside the chart. Use separate labels if your plan refers to both.

These terms describe where price sits within a selected interval. They do not measure fundamental value or predict direction. A close outside the selected high or low is a range break. Record it separately before deciding whether your rules allow a new range.

Update equilibrium only when the new range is known

For the update example, keep the original low. When a candle makes a higher high than both its neighbors, use it as a new high only after the right-hand candle closes. The 6,012.00 high is seen at 10:00, and the one-bar confirmation arrives at 10:05. This is the drill’s chosen update rule.

Freeze the old range in your journal. The 9:50 label uses the earlier midpoint of 6,003.00. The 10:10 comparison can use 6,005.00 because the new high was confirmed first. An equilibrium line is a reference for reviewing the setup. Conditions for a trade need their own rules.

Sources

Official References

Platform details on this page were checked against these official resources.

ICT core content on equilibrium and discountThe original mentorship lesson on the lower half of a range.ICT core content on equilibrium and premiumThe companion mentorship lesson on the upper half of a range.
Related Guides

Keep Building the Rule System

All ICT chart lessons

Compare the concepts and practice marking them in replay.

Fair Value Gap examples

Read bullish and bearish ICT fair value gaps on MES charts. Calculate consequent encroachment and distinguish a midpoint touch from a full revisit.

Balanced Price Range examples

Draw an ICT balanced price range from two opposing fair value gaps. Compare one-tick overlap and touching edges on paired MES charts.

Liquidity Sweep examples

Compare ICT liquidity sweeps with closes beyond the range on synthetic MES charts. Learn what a candle can tell you when it crosses both sides.

Market Structure Shift examples

Compare bullish and bearish ICT market structure shifts, a wick-only break, and two futures charts with the same shift that may or may not form a fair value gap.

Order Block examples

Compare bullish and bearish ICT order block examples on fictional MES candles. Mark the originating candle, confirming close and separate fair value gap.

Displacement Candle examples

Read bullish and bearish ICT displacement candles on fictional MES charts. Measure the body and close, and compare a wide wick that fails the rule.

Optimal Trade Entry examples

Draw an ICT Optimal Trade Entry zone on fictional MES candles. Use the 62%, 70.5%, and 79% levels, check valid ticks, and avoid hindsight in replay.

Kill Zones examples

Mark ICT kill zones in New York time on a futures chart. Use fictional MES bars to distinguish window boundaries, cash open and daylight saving.

SMT Divergence examples

Compare ICT SMT divergence examples on paired MES and MNQ charts. Match bar closes and use known reference highs or lows to check the disagreement.

Inversion Fair Value Gap examples

See an ICT inversion fair value gap form in both directions on fictional MES charts. Compare a confirming close beyond the zone with a wick-only break.

Breaker Block examples

Compare bullish and bearish ICT breaker blocks with a matching no-sweep example. See which candle confirms the break and when a retest can count.

Unicorn Model examples

Compare bullish and bearish ICT Unicorn setups on synthetic MES charts. Measure the breaker and fair value gap overlap, including a zero-width near miss.

Silver Bullet Times examples

Find the three ICT Silver Bullet times in New York, Chicago and UTC. Compare three fictional MES charts with gap confirmations and cutoff examples.

Power of Three examples

Compare bullish, bearish and failed ICT Power of Three sequences on synthetic MES charts. Freeze the range and check each phase in order.

Internal vs. External Range Liquidity examples

See where an internal fair value gap and an external range high sit on two synthetic MES charts. Label a price using a range fixed before the move.

Draw on Liquidity examples

Mark a prior session high or low before the move. Three fictional MES charts show the target first, the opposite side first, and a bar that reaches both.

Daily Bias examples

Learn how to write an ICT daily bias before the move and compare three fictional MES replays where the draw is met, invalidated or expires.

Judas Swing examples

Compare bullish, bearish and late-reclaim ICT Judas Swing examples on synthetic MES charts with a fixed overnight range and New York clock.

Practice range selection in Bar Replay

Record the original midpoint and the first time your chosen rule allows an update.

FAQ

Common Questions

How can price be in premium and discount at the same time?

It can sit above the midpoint of one range and below the midpoint of another. Record the ranges by name so your journal shows which one each label refers to.

Risk Disclosure

Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.

TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.

Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.