TradeReign
Back to HomeEducation HubCompatibilityAboutDisclosures
ICT Concepts for Futures

ICT Optimal Trade Entry Examples: Draw the OTE Zone Read the Annotated Futures Charts

Optimal Trade Entry, or OTE, is the ICT name for a deep retracement band. These examples show how to draw it in each direction and map the band to a futures tick grid. A touch tells you about the chart geometry. An entry rule and its order-fill assumptions are separate decisions.

Quick Answer

Measure one directional price leg and mark the band 62% to 79% back from the end of the move toward its origin. The middle reference is 70.5%. In this lesson the swing endpoint must be confirmed before you count a revisit.

Start 7-Day TrialMore Guides

Optimal Trade Entry chart examples

Synthetic MES 5-minute candles. Times are bar closes in ET.

Measure from the 6,000.00 low to the 6,010.00 high. The raw bullish band is 6,002.10–6,003.80, and the valid MES ticks inside it run from 6,002.25 to 6,003.75. After confirmation at 9:50 ET, the next bar reaches 6,003.25 inside the band.

Bullish retracement into the band

Measure from the 6,000.00 low to the 6,010.00 high. The raw bullish band is 6,002.10–6,003.80, and the valid MES ticks inside it run from 6,002.25 to 6,003.75. After confirmation at 9:50 ET, the next bar reaches 6,003.25 inside the band.

Bearish retracement into the band

Measure from the 6,010.00 high to the 6,000.00 low. The raw bearish band is 6,006.20–6,007.90. The ticks inside are 6,006.25–6,007.75. The 9:55 high reaches 6,006.75 after the 9:50 confirmation.

Near miss with only a pre-confirmation touch

The confirmation bar itself trades to 6,003.25. The high used as the endpoint is only confirmed when that bar closes at 9:50. The following bar stays above the band, so the replay rule records no eligible touch.

Set up the Fibonacci drawing on a clean swing

Choose the leg and the swing confirmation rule before looking for a retracement. On the example charts, the final high or low must have an adjacent bar on each side with a less extreme high or low. The right-hand candle has to close first.

In TradingView’s Fib Retracement tool, enable 0.62, 0.705 and 0.79. Verify that 0 is at the end of the leg and 1 is at its origin. If the values read backward, use Reverse or switch the anchor order.

Convert the raw band into valid MES ticks

For a rising leg, subtract the measured percentage of the leg’s range from the final high. For a falling leg, add it to the final low. On a 10-point leg, 70.5% is 7.05 points from the end, giving 6,002.95 in the bullish example and 6,007.05 in the bearish one.

Use the next tick at or above the lower boundary and the previous tick at or below the upper boundary to identify valid prices inside the band. That is how the charts translate a fractional boundary to 0.25-point MES ticks. If no valid tick remains, the geometric band contains no tradable price increment.

Sources

Official References

Platform details on this page were checked against these official resources.

The Inner Circle Trader’s OTE primerOriginal discussion of optimal trade entry.TradingView Fib Retracement settingsCustom ratios, anchors and the Reverse setting.
Related Guides

Keep Building the Rule System

All ICT chart lessons

Compare the concepts and practice marking them in replay.

Fair Value Gap examples

Read bullish and bearish ICT fair value gaps on MES charts. Calculate consequent encroachment and distinguish a midpoint touch from a full revisit.

Balanced Price Range examples

Draw an ICT balanced price range from two opposing fair value gaps. Compare one-tick overlap and touching edges on paired MES charts.

Liquidity Sweep examples

Compare ICT liquidity sweeps with closes beyond the range on synthetic MES charts. Learn what a candle can tell you when it crosses both sides.

Market Structure Shift examples

Compare bullish and bearish ICT market structure shifts, a wick-only break, and two futures charts with the same shift that may or may not form a fair value gap.

Order Block examples

Compare bullish and bearish ICT order block examples on fictional MES candles. Mark the originating candle, confirming close and separate fair value gap.

Displacement Candle examples

Read bullish and bearish ICT displacement candles on fictional MES charts. Measure the body and close, and compare a wide wick that fails the rule.

Kill Zones examples

Mark ICT kill zones in New York time on a futures chart. Use fictional MES bars to distinguish window boundaries, cash open and daylight saving.

SMT Divergence examples

Compare ICT SMT divergence examples on paired MES and MNQ charts. Match bar closes and use known reference highs or lows to check the disagreement.

Inversion Fair Value Gap examples

See an ICT inversion fair value gap form in both directions on fictional MES charts. Compare a confirming close beyond the zone with a wick-only break.

Breaker Block examples

Compare bullish and bearish ICT breaker blocks with a matching no-sweep example. See which candle confirms the break and when a retest can count.

Unicorn Model examples

Compare bullish and bearish ICT Unicorn setups on synthetic MES charts. Measure the breaker and fair value gap overlap, including a zero-width near miss.

Silver Bullet Times examples

Find the three ICT Silver Bullet times in New York, Chicago and UTC. Compare three fictional MES charts with gap confirmations and cutoff examples.

Power of Three examples

Compare bullish, bearish and failed ICT Power of Three sequences on synthetic MES charts. Freeze the range and check each phase in order.

Dealing Range examples

Mark an ICT dealing range on synthetic MES charts. Calculate equilibrium and see why the same price can be premium in one range and discount in another.

Internal vs. External Range Liquidity examples

See where an internal fair value gap and an external range high sit on two synthetic MES charts. Label a price using a range fixed before the move.

Draw on Liquidity examples

Mark a prior session high or low before the move. Three fictional MES charts show the target first, the opposite side first, and a bar that reaches both.

Daily Bias examples

Learn how to write an ICT daily bias before the move and compare three fictional MES replays where the draw is met, invalidated or expires.

Judas Swing examples

Compare bullish, bearish and late-reclaim ICT Judas Swing examples on synthetic MES charts with a fixed overnight range and New York clock.

Check the contract’s tick size

Verify the actual minimum increment before converting a zone to valid price levels.

FAQ

Common Questions

Does a touch at 70.5% confirm an order fill?

The 70.5% line is a geometric reference and can sit between ticks. A chart touch and a resting order fill are separate. Define size, order type and fill assumptions independently in replay.

Risk Disclosure

Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.

TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.

Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.