Gap and revisit inside
The 6,000.75–6,002.25 gap confirms at 10:50 ET. The next candle’s low reaches 6,001.50 and the bar closes at 10:55. Both timestamps are inside the 10:00–11:00 example window.

Synthetic MES 5-minute candles. Times are bar closes in ET.
The 6,000.75–6,002.25 gap confirms at 10:50 ET. The next candle’s low reaches 6,001.50 and the bar closes at 10:55. Both timestamps are inside the 10:00–11:00 example window.
The 6,000.75–6,002.25 gap confirms at 10:50 ET. The next candle’s low reaches 6,001.50 and the bar closes at 10:55. Both timestamps are inside the 10:00–11:00 example window.
The gap is known at 10:55. The bar closing at 11:00 stays above it, and the first revisit happens in the bar that opens at 11:00. The replay rule logs a valid gap and no eligible revisit.
The third bar opens inside the hour at 10:55 and closes exactly at 11:00. A chart based on bar opens can shade it inside the window. Under the exercise’s close-based rule, the gap is confirmed too late.
The window names describe the model. All three start from New York local time, including the one labeled London. Chicago is one hour earlier.
If you are outside North America, convert using the actual trading date. Different regions change their clocks on different dates.
On a dated intraday futures chart, set the TradingView Trading Sessions indicator’s time zone to America/New_York. Set the three start and end times from the New York column. Use Electronic Trading Hours if the regular session setting hides the overnight window.
Verify the session shading using a bar near each boundary. TradingView includes a candle by its opening time. The chart examples here print close times, which explain when a close-based rule can act.
First record when the third candle confirms the gap. Then record the first later revisit, with the observed time and your decision time. A five-minute bar can show that the zone traded during the interval. An order fill requires its own model and an order that could already have been working.
The close-based cutoff on this page is a teaching convention. For any playbook, write whether the window gates setup detection, new orders or fills, and specify what happens to open positions and working orders at the end. A time label alone gives no entry or exit signal.
Platform details on this page were checked against these official resources.
Compare the concepts and practice marking them in replay.
Read bullish and bearish ICT fair value gaps on MES charts. Calculate consequent encroachment and distinguish a midpoint touch from a full revisit.
Draw an ICT balanced price range from two opposing fair value gaps. Compare one-tick overlap and touching edges on paired MES charts.
Compare ICT liquidity sweeps with closes beyond the range on synthetic MES charts. Learn what a candle can tell you when it crosses both sides.
Compare bullish and bearish ICT market structure shifts, a wick-only break, and two futures charts with the same shift that may or may not form a fair value gap.
Compare bullish and bearish ICT order block examples on fictional MES candles. Mark the originating candle, confirming close and separate fair value gap.
Read bullish and bearish ICT displacement candles on fictional MES charts. Measure the body and close, and compare a wide wick that fails the rule.
Draw an ICT Optimal Trade Entry zone on fictional MES candles. Use the 62%, 70.5%, and 79% levels, check valid ticks, and avoid hindsight in replay.
Mark ICT kill zones in New York time on a futures chart. Use fictional MES bars to distinguish window boundaries, cash open and daylight saving.
Compare ICT SMT divergence examples on paired MES and MNQ charts. Match bar closes and use known reference highs or lows to check the disagreement.
See an ICT inversion fair value gap form in both directions on fictional MES charts. Compare a confirming close beyond the zone with a wick-only break.
Compare bullish and bearish ICT breaker blocks with a matching no-sweep example. See which candle confirms the break and when a retest can count.
Compare bullish and bearish ICT Unicorn setups on synthetic MES charts. Measure the breaker and fair value gap overlap, including a zero-width near miss.
Compare bullish, bearish and failed ICT Power of Three sequences on synthetic MES charts. Freeze the range and check each phase in order.
Mark an ICT dealing range on synthetic MES charts. Calculate equilibrium and see why the same price can be premium in one range and discount in another.
See where an internal fair value gap and an external range high sit on two synthetic MES charts. Label a price using a range fixed before the move.
Mark a prior session high or low before the move. Three fictional MES charts show the target first, the opposite side first, and a bar that reaches both.
Learn how to write an ICT daily bias before the move and compare three fictional MES replays where the draw is met, invalidated or expires.
Compare bullish, bearish and late-reclaim ICT Judas Swing examples on synthetic MES charts with a fixed overnight range and New York clock.
Advance through the last two bars of the window and log the first time each event became knowable.
They stay fixed in New York local time. Their UTC times shift one hour when New York switches between standard time and daylight time. Use a regional chart time zone and check the trading date.
Futures trading contains substantial risk and is not suitable for every investor. TradeReign is a trading-discipline and rule-enforcement application. It does not provide trading advice, trade signals, investment recommendations, or performance guarantees.
TradeReign is not a broker-dealer, futures commission merchant, or investment advisor.
Futures trading contains substantial risk and is not for every investor. An investor could potentially lose all or more than the initial investment. Only risk capital - money that can be lost without jeopardizing financial security or lifestyle - should be used for trading. Past performance is not necessarily indicative of future results.